How To Fix iPhone Screen Flickering After Water Damage

iPhone Screen Flickering After Water Damage

Dealing with an iPhone screen that flickers after water damage is frustrating. First, quickly remove your phone from the water, then turn it off immediately. To get rid of the moisture, don’t use heat sources like a hairdryer. That may end up damaging your phone’s internal components. Instead, try the rice trick, silica gel packs, or the vacuum method. They are much safer and more effective, although they require patience. However, if these don’t work, it might be best to get them fixed by a professional. Let’s look at each step in more depth.

Ways to Fix iPhone Screen Flickering After Water Damage

Let’s examine the most important things you can do to fix your iPhone.

1: Power Off Your Device

To avoid short circuits, turn off your iPhone right away. Wait for “slide to power off” to show up, then press and hold the power button. If your screen won’t respond, press and hold the side button and volume up and down simultaneously to force shutdown. Turn it off and leave it off the whole time it’s drying. Let the phone dry for 48 to 72 hours is recommended for the best results.

2: Use Alcohol for Cleaning

Don’t put your iPhone near a hair dryer, microwave, oven, or direct sunlight when drying it. These can damage delicate parts, warp the screen, or push water deeper into the device. Instead, use rubbing alcohol on a cotton swab to clean the ports and a soft, lint-free cloth to wipe the outside gently.

3: Try The Rice Trick

For at least 48 hours, place your powered-off iPhone in a jar of raw rice. The rice soaks up the device’s wetness. It’s important not to check your phone right away. Patience is very important. This method works for small amounts of water damage but doesn’t always work for big problems. Don’t let rice grains get near ports.

4: Using Silica Gel Packs

If your device has been accidentally dropped in water, silica gel packets work better than rice. For 48 to 72 hours, put a few packets in a ziplock bag with your iPhone. This makes an environment very good at absorbing water, which pulls water from deep inside your device. Electronics shops sell bigger packs that are made just for drying electronics.

5: Vacuum Method

To gently dry out ports and buttons, use a vacuum cleaner with a small adapter set to its lowest setting. Hold the vacuum tip about half an inch away from the device and use light suction for 10 to 15 seconds per port. The vacuum method can help draw out some moisture after water damage, which prevents further damage to your iPhone. 

6: Professional Repair Services

If the screen still flickers after trying these fixes, you should seek help from expert iPhone repair services. Water can damage the screen, the logic board, or the links between the screens. Professional techs have the right tools to find and fix these problems correctly, which could keep you from buying a whole new device. 

Can My iPhone Screen Recover From Water Damage?

It is possible, yes. If the water didn’t damage the display parts permanently, an iPhone screen may be able to be fixed after being damaged by water. Recovery depends on:

  • How quickly you removed your iPhone from the water
  • How deep the water gets into your device
  • Whether electricity was running through the wires when water hit them

Minor screen flickering caused by a small amount of wetness usually disappears after the right drying methods are used. But if the liquid corroded the connection points or hurt the display driver, the screen might still flicker or have other issues after drying it. In these situations, it’s generally necessary to replace the part.

Remember that even if the screen looks fine after it has dried, rust that isn’t seen can still damage your phone over time, so it’s important to keep an eye on it for a few days. 

Why Is My iPhone Screen Flickering After Water Damage?

When your iPhone gets wet, the electrical links between its parts get messed up, which causes the screen to flicker. In particular, water can:

  • Cause short circuits in the wires that connect to the display.
  • Make the link points between the screen and logic board rust.
  • Break the integrated circuit for the display driver
  • Make the power going to the monitor inconsistent.

This flickering usually happens when these links work sometimes but not other times. Water makes weak links that quickly form and break apart as the water moves or evaporates, making the screen flicker.

Even after the water has dried, salt, minerals, and other elements can speed up rust. This is why professional cleaning may still be needed even after trying to dry the water at home.

Conclusion

When your iPhone screen flickers due to water exposure or turns on but the screen is black, act quickly to remove it from the water and power it off. Stay clear of heat sources, as they can cause additional harm. Dry your phone using silica gel packs for 72 hours, the rice trick for 48 hours, or vacuum the ports to remove moisture. If the flickering continues, contact professional iPhone screen repair services like Cell N Tech for expert help.